1.Observe the general safety operation regulations of Laser CNC Equipment. Start the laser machine strictly in accordance with the laser machine startup procedure.
2. Operators must be trained to be familiar with the structure and performance of the equipment, and master the knowledge of the operating system.
3. Wear labor protection equipment according to regulations, and must wear protective glasses that meet the regulations near the laser beam.
4. Do not process a material before it is clear whether it can be irradiated or heated by a laser to avoid the potential danger of smoke and vapor.
5. When the equipment is started, the operator shall not leave the post or be taken care of without authorization. If it is necessary to leave, stop the machine or cut off the power switch.
6. Keep the fire extinguisher within easy reach; turn off the laser or shutter when not working; do not place paper, cloth or other flammable materials near the unprotected laser beam.
7. When an abnormality is found during processing, the machine should be shut down immediately, and the fault should be eliminated or reported to the supervisor.
8. Keep the laser, the bed and the surrounding area clean, orderly, and free of oil pollution, and stack the workpieces, plates, and waste materials as required.
9. When using gas cylinders, avoid crushing the welding wires to avoid leakage accidents. The use and transportation of gas cylinders should comply with gas cylinder supervision regulations. It is forbidden to explode gas cylinders in the sun or close to heat sources. When opening the bottle valve, the operator must stand on the side of the bottle mouth.
10. Observe high-voltage safety regulations when repairing. Every 40 hours of operation or weekly maintenance, every 1,000 hours of operation or every six months of maintenance shall be carried out in accordance with regulations and procedures.
11. After starting the machine, manually start the machine in the X and Y directions at low speed, and check whether there is any abnormality.
12. After inputting the new part program, test run it first and check its operation.
13. When working, pay attention to observe the operation of the machine tool to avoid accidents caused by the cutting machine going out of the effective stroke range or two collisions.
A piece of laser cutting machine equipment is tens of thousands or even hundreds of thousands, so you must pay attention to it in operation, and usually pay attention to maintenance and maintenance to increase the service life of the equipment, save costs, and create greater benefits.
Laser Cutter Machine
1.Necessary protective equipment for laser cutting machine.
The typical protective equipment for Laser Cutter Machine is laser protective glasses, because protective glasses that prevent laser damage to human eyes can be divided into reflection, absorption, diffraction and composite types according to their protection principles. Of course, they It will be filtered and protected according to the laser radiation wavelength of the laser cutting machine to achieve the protection of the laser cutting machine laser of the human body. This is also the safer and convenient protective equipment for the laser cutting machine on the market.
2. Self-protection against radiation of laser cutting machine.
If the human body has enough health, it can resist the slight radiation of the laser cutting machine. Therefore, the laser cutting machine operator should pay attention to eat more carrots, bean sprouts, tomatoes, lean meat, animal liver and other foods rich in vitamin A, C and protein, and often drink green tea and so on. Because these foods can help humans to better protect the eyes, and the human body can better protect the human body under the conditions of laser cutting machine radiation.
First of all, you need to know the graphics in PDF format and learn how to operate the software that comes with the machine. (The use of the software requires the installation of the software, the dongle, the software cannot be opened without the dongle. The installation sequence is to install the data transmission port and the dongle driver first and then install the operating software. The software has power, speed and other adjustments. Because of the material The thickness of the material varies. Thick and difficult to cut the power is high and the speed is slow, and vice versa. For power adjustment, you can use the dot shot on the operation panel of the machine to test whether the power can cut through the material. This is the computer, and the machine operation panel. There are internal control and external control. Internal control is the control of the machine itself, and external control is computer control. Use the operating software to download the PDF graphics of the cutting machine to the machine chip, and press the arrow keys on the machine operation panel to select a starting point. Then press the start button to start cutting.
If necessary, please contact the Laser CNC Equipment Supplier
Copyright：@2020-2021
Comments Please sign in or sign up to post.
0
0 of 500 characters used